Journal Watch · ACS Nano · 2026

Mapping MXene Alignment under Shear: An In Situ SAXS Study of Size-Dependent Orientation Dynamics.

These findings provide key insights for fabricating ordered structures from MXene dispersions and other anisotropic nanomaterials, highlighting the importance of understanding orientation dynamics to advance solution-based processing.

Zhang J, Lynch PA, Usman KAS et al.ACS Nano3 min readPharma relevance 55/100

DOI: 10.1021/acsnano.5c22370PMID: 41705519Study type: research study

TL;DR

These findings provide key insights for fabricating ordered structures from MXene dispersions and other anisotropic nanomaterials, highlighting the importance of understanding orientation dynamics to advance solution-based processing.

Key findings

  • Conversely, small sheets (∼250 nm) require a minimum shear rate (0.11 s<sup>-1</sup>) to align but lose order rapidly, particularly at low concentrations (e.g., 25 s at 1 mg mL<sup>-1</sup>).
  • Fiber wet-spinning experiments further demonstrate how the shear rate directly dictates sheet alignment and, consequently, the electrical conductivity of the resulting fibers.
  • These findings provide key insights for fabricating ordered structures from MXene dispersions and other anisotropic nanomaterials, highlighting the importance of understanding orientation dynamics to advance solution-based processing.

What they did

We specifically examine the interplay among sheet sizes, concentrations, and shear rates in driving orientation. Our results reveal a strong size-dependent behavior. Large sheets (∼5 μm) at a high concentration (30 mg mL<sup>-1</sup>) spontaneously align into stable liquid crystalline phases.

Full abstract (original)

Background: Effective control over the alignment of 2D nanomaterials in solution is critical for optimizing their macroscopic properties. However, the fundamental factors governing this alignment remain poorly understood. This study addresses this gap by investigating the disorder-to-order transition states of Ti<sub>3</sub>C<sub>2</sub>T<sub><i>x</i></sub> MXene sheets.

What they did: We specifically examine the interplay among sheet sizes, concentrations, and shear rates in driving orientation. Our results reveal a strong size-dependent behavior. Large sheets (∼5 μm) at a high concentration (30 mg mL<sup>-1</sup>) spontaneously align into stable liquid crystalline phases.

Results & conclusions: Conversely, small sheets (∼250 nm) require a minimum shear rate (0.11 s<sup>-1</sup>) to align but lose order rapidly, particularly at low concentrations (e.g., 25 s at 1 mg mL<sup>-1</sup>). Fiber wet-spinning experiments further demonstrate how the shear rate directly dictates sheet alignment and, consequently, the electrical conductivity of the resulting fibers. These findings provide key insights for fabricating ordered structures from MXene dispersions and other anisotropic nanomaterials, highlighting the importance of understanding orientation dynamics to advance solution-based processing.

Abstract © the authors / ACS Nano (2026). Reproduced here for discussion and indexing, with attribution. Read the original at https://doi.org/10.1021/acsnano.5c22370 · PubMed 41705519.

Why it matters for pharma & biotech

  • Relevant to Biotechnology & Methods teams tracking ACS Nano for new targets, mechanisms and biomarkers.
  • As earlier-stage work, its near-term value is target validation and assay design rather than clinical decisions.
  • For searchers: the full abstract is reproduced below, so you can judge relevance before opening the publisher page.

Limitations & what to check in the full text

  • This brief is based on the published abstract only. Effect sizes, subgroup results and safety detail in the full text may qualify the headline findings.
  • The abstract reports its conclusions qualitatively, without headline effect sizes — read the full text before citing a magnitude.

Frequently asked questions

What did this ACS Nano study find?

These findings provide key insights for fabricating ordered structures from MXene dispersions and other anisotropic nanomaterials, highlighting the importance of understanding orientation dynamics to advance solution-based processing.

What type of study is this?

It is a research study, published in ACS Nano in 2026. We specifically examine the interplay among sheet sizes, concentrations, and shear rates in driving orientation.

Where can I read the original paper?

The original is at the publisher via DOI 10.1021/acsnano.5c22370. PubMed ID: 41705519. BioStudioAI reproduces the abstract for discussion and links to the source.

How to cite the original: Zhang J, Lynch PA, Usman KAS et al.. Mapping MXene Alignment under Shear: An In Situ SAXS Study of Size-Dependent Orientation Dynamics.. ACS Nano (2026). DOI: 10.1021/acsnano.5c22370.
This brief: BioStudioAI Journal Watch, 29 October 2026. https://biostudioai.com/blog/papers/mapping-mxene-alignment-under-shear-an-in-situ-saxs-study-of-size-depend-c22370/

Reading papers is step one. Analysing the data is the work.

BioStudioAI turns raw lab files into QC'd results, statistics, figures, reports and slides — hosted on your servers, every number computed, nothing typed.

Open BioStudioAI More guides