Journal Watch · ACS Nano · 2026

Frank-van der Merwe-Mediated Sequential Thermal Evaporation for Stable FASnI<sub>3</sub> Perovskite Solar Cells.

These findings provide valuable insights into the scalable fabrication of high-quality and stable lead-free perovskite thin films for high-performance optoelectronics.

Wang Z, He D, Steele JA et al.ACS Nano3 min readPharma relevance 30/100

DOI: 10.1021/acsnano.5c16992PMID: 41405218Study type: research study

TL;DR

These findings provide valuable insights into the scalable fabrication of high-quality and stable lead-free perovskite thin films for high-performance optoelectronics.

Key findings

  • Benefiting from the SnI<sub>2</sub> underlayer, the FASnI<sub>3</sub>-based PSCs achieve a champion power conversion efficiency (PCE) of 5.51%.
  • The unencapsulated devices exhibit negligible current-voltage hysteresis and impressive stability, retaining over 91.98% of the initial PCE after 2100 h in a nitrogen atmosphere.
  • These findings provide valuable insights into the scalable fabrication of high-quality and stable lead-free perovskite thin films for high-performance optoelectronics.

Numbers at a glance (from the abstract)

5.51%91.98%

Every figure above is taken verbatim from the abstract below. Check the full text for denominators, confidence intervals and subgroup detail.

What they did

Herein, we develop a sequential thermal evaporation strategy, in which the different growth modes of SnI<sub>2</sub> and FAI thin films on the substrate are precisely regulated to guide perovskite crystallization for improving film quality. We found that the FASnI<sub>3</sub> film follows a Frank-van der Merwe growth mode owing to the lower surface free energy of the first evaporated SnI<sub>2</sub> underlayer, which further promotes the formation of high-quality perovskite thin films with a preferred out-of-plane orientation, homogeneous Sn distribution, and suppressed interfacial defects.

Full abstract (original)

Background: Thermal evaporation provides a solvent-free and scalable process for thin-film deposition with high reproducibility, which is particularly attractive for fabricating oxygen- and solvent-sensitive tin-based halide perovskites. However, fully thermally evaporated FASnI<sub>3</sub> perovskites have been well underexplored, and the film quality is hindered by uncontrolled crystallization and high defect density.

What they did: Herein, we develop a sequential thermal evaporation strategy, in which the different growth modes of SnI<sub>2</sub> and FAI thin films on the substrate are precisely regulated to guide perovskite crystallization for improving film quality. We found that the FASnI<sub>3</sub> film follows a Frank-van der Merwe growth mode owing to the lower surface free energy of the first evaporated SnI<sub>2</sub> underlayer, which further promotes the formation of high-quality perovskite thin films with a preferred out-of-plane orientation, homogeneous Sn distribution, and suppressed interfacial defects.

Results & conclusions: Benefiting from the SnI<sub>2</sub> underlayer, the FASnI<sub>3</sub>-based PSCs achieve a champion power conversion efficiency (PCE) of 5.51%. The unencapsulated devices exhibit negligible current-voltage hysteresis and impressive stability, retaining over 91.98% of the initial PCE after 2100 h in a nitrogen atmosphere. These findings provide valuable insights into the scalable fabrication of high-quality and stable lead-free perovskite thin films for high-performance optoelectronics.

Abstract © the authors / ACS Nano (2026). Reproduced here for discussion and indexing, with attribution. Read the original at https://doi.org/10.1021/acsnano.5c16992 · PubMed 41405218.

Why it matters for pharma & biotech

  • Relevant to Biotechnology & Methods teams tracking ACS Nano for new targets, mechanisms and biomarkers.
  • As earlier-stage work, its near-term value is target validation and assay design rather than clinical decisions.
  • For searchers: the full abstract is reproduced below, so you can judge relevance before opening the publisher page.

Limitations & what to check in the full text

  • This brief is based on the published abstract only. Effect sizes, subgroup results and safety detail in the full text may qualify the headline findings.

Frequently asked questions

What did this ACS Nano study find?

These findings provide valuable insights into the scalable fabrication of high-quality and stable lead-free perovskite thin films for high-performance optoelectronics.

What type of study is this?

It is a research study, published in ACS Nano in 2026. Herein, we develop a sequential thermal evaporation strategy, in which the different growth modes of SnI<sub>2</sub> and FAI thin films on the substrate are precisely regulated to guide perovskite crystallization for improving film quality.

Where can I read the original paper?

The original is at the publisher via DOI 10.1021/acsnano.5c16992. PubMed ID: 41405218. BioStudioAI reproduces the abstract for discussion and links to the source.

How to cite the original: Wang Z, He D, Steele JA et al.. Frank-van der Merwe-Mediated Sequential Thermal Evaporation for Stable FASnI&lt;sub&gt;3&lt;/sub&gt; Perovskite Solar Cells.. ACS Nano (2026). DOI: 10.1021/acsnano.5c16992.
This brief: BioStudioAI Journal Watch, 29 October 2026. https://biostudioai.com/blog/papers/frank-van-der-merwe-mediated-sequential-thermal-evaporation-for-stable-f-c16992/

Reading papers is step one. Analysing the data is the work.

BioStudioAI turns raw lab files into QC'd results, statistics, figures, reports and slides — hosted on your servers, every number computed, nothing typed.

Open BioStudioAI More guides